Finished Circumference About 20" (51 cm), will stretch to fit a range of sizes.
12 sts = about 4" (10 cm) in pattern.
BE SURE TO CHECK YOUR GAUGE.
2/2 RC (2 over 2 right cross) Slip 2 sts to cable needle and hold in back, k2, then k2 from cable needle.
3/3 RC (3 over 3 right cross) Slip 3 sts to cable needle and hold in back, k3, then k3 from cable needle.
M1 (make 1) An increase worked by lifting the horizontal strand lying between needles and placing it onto the left needle. Knit this new stitch through the back loop – 1 st increased.
s2kp Slip next 2 sts as if to knit them tog, knit 1, pass the 2 slipped sts up and over the knit st and off the needle – 2 sts decreased.
ssk (slip, slip, knit) Slip next 2 sts as if to knit, one at a time, to right needle; insert left needle into fronts of these 2 sts and knit them tog – 1 st decreased.
Hat is worked in the rnd on double pointed needles.
Hat can be worked by following written instructions by reading Chart. When working from Chart, read all rnds of Chart from right to left.
Cast on 40 sts. Divide sts onto 4 needles, with 10 sts on each needle. Place marker for beg of rnd. Join by working the first st on left hand needle with the working yarn from the right hand needle and being careful not to twist sts.
Rnds 1-3: *K1 tbl, p1; rep from * around.
Rnd 4 (Increase Rnd): *K1 tbl, p1, (M1, k1) 3 times, p1, k1 tbl, M1, p1, M1, k1, p1; rep from * around – 60 sts (15 sts on each needle).
Rnd 5: *K1 tbl, p1, k6, p1, k1 tbl, p2, k1, p2; rep from * around.
Rnd 6: *K1 tbl, p1, k6, p1, k1 tbl, p1, (k1, p1) twice; rep from * around.
Rnd 7: Rep Rnd 5.
Rnd 8: *K1 tbl, p1, 3/3 RC, p1, k1 tbl, p1, (k1, p1) twice; rep from * around.
Rnds 9-14: Rep Rnds 5 and 6.
Rnd 15: Rep Rnd 5.
Rnd 16: Rep Rnd 8.
Shape Crown (Top of Hat)
Rnd 1 (Decrease Rnd): *K1 tbl, p1, k6, p1, k1 tbl, p1, s2kp, p1; rep from * around – 52 sts.
Rnd 2: *K1 tbl, p1, k6, p1, k1 tbl, p3; rep from * around.
Rnd 3: *K1 tbl, p1, k6, p1, k1 tbl, p1, k1, p1; rep from * around
Rnd 4 (Decrease Rnd): *K1 tbl, p1, k6, p1, k1 tbl, p3tog; rep from * around – 44 sts.
Rnd 5 (Decrease Rnd): Remove beg of rnd marker, k1 tbl, return marker to needle for new beg of rnd, *p1, k6, p1, k3tog; rep from * around – 36 sts.
Rnd 6 (Decrease Rnd): *P1, k1, ssk, k2tog, k1, p1, k1 tbl; rep from * around – 28 sts.
Rnd 7: *P1, 2/2 RC, p1, k1 tbl; rep from * around.
Rnd 8 (Decrease Rnd): *K2tog, k2, ssk, k1 tbl; rep from * around – 20 sts.
Rnd 9 (Decrease Rnd): *K2tog; rep from * around – 10 sts.
Rnd 10 (Decrease Rnd): *K2tog; rep from * around – 5 sts.
Cut yarn, leaving a long yarn tail. Thread yarn tail into blunt needle and then through remaining sts, pull to gather. Knot to secure.
Tassel”¨Wrap yarn around the 6" (15 cm) side of cardboard 35 times. Cut an 18" (45.5 cm) length and thread, doubled, into blunt needle. Insert needle under all strands at upper edge of cardboard. Pull tightly and knot securely near strands. Cut yarn loops at lower edge of cardboard. Cut another 18" (45.5 cm) long length of yarn and wrap tightly around loops 1-1/2" (4 cm) below top knot to form Tassel neck. Knot securely; thread ends into needle and weave ends to center of Tassel. Trim Tassel ends evenly. Tie Tassel to top of Hat.
Weave in ends.
beg = begin(ning)(s)
k = knit
k2tog = knit 2 stitches together
k3tog = knit 3 stitches together
p = purl
p3tog = purl 3 stitches together
rep = repeat
rnd(s) = round(s)
st(s) = stitch(es)
tbl = through back loop
SHIPPINGShipping your purchase is easy at JOANN! Orders typically leave our warehouses within 1-3 business days (Mon-Fri). Delivery date depends on the destination address and the shipping method. You’ll receive an email with tracking information when your order is shipped.
RETURNSReturns can be made for FREE in any of our stores.