Images

Wedding Decor Ideas
Reset

Wedding Decor Ideas

Crafting Time:
  • 1-2 Hours
Skill Level:
  • Beginner
Project Courtesy of: Jo-Ann Fabric and Craft Stores
Print Project Description Add to Project List

Additional Information

Description

Wedding Invitation, accessory cards & envelopes

SUPPLIES & TOOLS:

  • Cardstock – 4 coordinating
  • Corrugated paper
  • Gold ink pad
  • Self-adhesive pearl dots
  • Gold foil card & envelope pack
  • Flower punch
  • Adhesive squares
  • Glue stick
  • Paper trimmer
  • Scissors & scallop shears
  • Pencil

DIRECTIONS:
    For Invitations:
  1. Determine the preferred order of 4 paper layers. Cut the largest to fit inside a standard envelope size. Cut the remaining papers in gradually smaller sizes. Print the invitation information on the smallest panel. Ink the edges and adhere to the next larger panel.
  2. Continue for 3 panels. Attach a narrow strip of one of the papers across the top of the invitation, securing on the back. Attach the final and largest panel.
  3. Punch a small flower from corrugated cardboard and adhere a pearl at the center. Set aside.
  4. Fold paper for leaves in half, crease neatly, and cut two leaves. Attach to the invitation and adhere the flower on top.
    For Accessory Cards and Envelopes:
  1. Using the photo as a guide, make a small printed tag. Mount twice and attach to a 4X4 pink square. Ink the edges, attach a small flower and pearl. Cut two leaves. Attach all to a gold foil card.
  2. To line envelope trace the point onto the back of the liner paper. Cut with scallop shears, trim to correct width, and lightly glue to inside of envelope.

Wedding Garland

SUPPLIES & TOOLS:

  • Cardstock – 3 coordinating
  • Cricut® machine & alphabet cartridge
  • Pink corrugated cardboard
  • Self-adhesive pearl dots
  • Gold cord
  • Pink tulle spool
  • Needle and pink thread
  • Glue stick
  • Paper trimmer
  • Scissors

DIRECTIONS:
  1. Cut “MR&MRS” letters using the Cricut® machine.
  2. Cut tags in a size to accommodate the letters. Glue the letters to the tag panel, then mount a second and third time.
  3. Cut rectangles of corrugated cardboard to fit over the top of the tags with enough space to slide the gold cord through. Glue the rectangles into place on edges only, leaving a “sleeve” for cord and for adjusting the tags. Adhere two pearls to each rectangle. Slide letters onto cord.
  4. Make two tulle flowers: Cut 2 yards of tulle and fold in half several times and then in half the other direction, until there is a square large enough to cut a round flower from. Stitch through the stack of tulle several times to secure. Trim the stack to create a circle around the stitching and then twist the flower to give it dimension. Repeat.
  5. Wrap strip of tulle around the gold cord between letters on tags. Stitch the ends of the tulle and the flowers to knotted loops at each end of the cord. Tie on additional strips of tulle at ends for swags.

Table Number

SUPPLIES & TOOLS:

  • Small birdcage candle-holder
  • Candle
  • Gold spray paint
  • Pick with spiral at end
  • Cardstock – 3 coordinating
  • Ribbon
  • Burlap flower
  • Gold Foil note card pack
  • Gold inkpad
  • Paper trimmer
  • Scissors & scallop shears
  • Adhesive tabs
  • Zots (3-D)
  • Aleene’s tacky glue

DIRECTIONS:
  1. Spray the birdcage gold.
  2. Cut two circles, one larger than the other, using scallop shears, to serve as base. Glue cage to base.
  3. Weave ribbon through the bars of the cage and tie into a bow at the front. Attach the burlap flower with the Zot.
  4. Print a card with the word “Table ___” on a panel. Mount once again on coordinating paper and then onto the front of a note card which has been trimmed to size. Insert into the pick.

Paper-covered Gift Boxes

SUPPLIES & TOOLS:

  • Gift boxes
  • Cardstock (box covering, tag, “&”)
  • Gold cardstock (leaves)
  • “&” Punch
  • Paper trimmer
  • Scissors
  • Mini hole punch
  • Glue stick
  • Ribbon, tulle, burlap flowers to embellish
  • Cardstock scrap, thread, mini hole punch
  • Gold ink pad (optional)
  • Thread
  • Zot (3-D)

DIRECTIONS:
  1. Assemble the box and measure the front panel. Cut cardstock to slightly smaller than the panel to be covered. Apply glue to the back and center the cardstock panel onto the box; press into place.
  2. Continue with all other sides and top of box.
  3. Embellish with ribbons and/or tulle and burlap flower.
  4. Cut a gold leaf or two for each package, and attach.
  5. Make a small “thank you” tag, punch a small hole, and tie onto package with thread.
  6. Punch an “&” and attach to “thank you” tag.

Embellished Bird Cage:

SUPPLIES & TOOLS:

  • Bird cage
  • Gold spray paint
  • Flowers – lace, burlap, etc.
  • Cardstock – Ivory, Pink, Gold metallic, Gold linen weave
  • Wide Satin Ribbon
  • Lace
  • Trim with beads
  • Edge punch
  • Adhesive – strip or Zots
  • Tacky glue
  • Paper trimmer
  • Scissors
  • Gold wire & cutters

DIRECTIONS:
  1. Spray the birdhouse gold.
  2. Depending upon the style of the birdhouse, attach lace, edge-punched cardstock strips, satin ribbon, and trim around the circumference, just below the latch and at the base.
  3. Wire and/or glue a variety of flowers to the cage.
  4. Make a tag that says “Cards,” and ink the edges. Mount on two more layers and glue to the cage at an angle.
  5. Tie on additional ribbon or lace to hang down the corner of the cage.
  6. Cut leaves and insert where needed in the flower arrangement.
  7. Cut cardstock to line the bottom floor of the birdhouse.

Reviews
CUSTOMERS ALSO VIEWED