PxPixel
How To Make a Bar Necklace | JOANN

How To Make a Bar Necklace

By Impressart

(0.0)
ITEM # 48913749P4

How To Make a Bar Necklace

By Impressart

ITEM # 48913749P4
Print Description

Crafting Time:
1-2 Hours
Skill Level:
Intermediate

DESCRIPTION +

SUPPLIES & TOOLS:
  • ImpressArt Charlotte Letters: uppercase & lowercase
  • ImpressArt Ergo-Angle metal stamping hammer
  • ImpressArt steel block
  • ImpressArt 3mm whimsy heart
  • ImpressArt flush cutters
  • ImpressArt chain nose pliers (2)
  • ImpresArt Alkeme stamping blank: 1 1/2" x 1/4" rectangle
  • ImpressArt stamp enamel marker
  • ImpressArt 7mm jump rings (2)
  • ImpressArt stamp guides
  • Soft cloth
  • 18" finished chain

DIRECTIONS:
  1. Using a ruler and a marker, indicate the center of your blank and the desired location for your jump ring holes at the top corners of your blank.
  2. Place your straight stamp guide along the bottom of your blank so that the orange line on the guide lines up with the center.
  3. Write the letters of your choice on the tape for reference and to help with spacing.
  4. Select your first stamp. When holding the stamp, make sure the ImpresssArt logo is facing you so the letter or design will be stamped in the correct orientation.
  5. Hold your stamp on the blank and lightly drag it toward the edge of the tape; strike each letter once with medium force.
  6. Using the hole punch pliers, punch hole if your previously marked area.
  7. Highlight your impression with the enamel marker. Wait 1-3 minutes and wipe away excess with a soft cloth.
  8. Find the center of your 18" chain, and cut at center link using the flush cutters.
  9. Use two pairs of chain nose pliers to open the jump ring laterally.
  10. Thread the jump ring through the first hole and attach to the end link of the 18" chain.
  11. Close the jump ring by bending it laterally so that the ends pass one another.
  12. Apply the last 3 steps to the other side.

REVIEWS

+
<ul id="BVSEOSDK_meta" style="display: none !important;"> <li data-bvseo="sdk">bvseo_sdk, dw_cartridge, 18.2.0, p_sdk_3.2.0</li> <li data-bvseo="sp_mt">CLOUD, getReviews, 31ms</li> <li data-bvseo="ct_st">reviews, product</li> <li data-bvseo="ms">bvseo-msg: Unsuccessful GET. status = 'ERROR', msg = 'Not Found.';</li> </ul>
SUPPLIES & TOOLS:
DIRECTIONS:
  1. Using a ruler and a marker, indicate the center of your blank and the desired location for your jump ring holes at the top corners of your blank.
  2. Place your straight stamp guide along the bottom of your blank so that the orange line on the guide lines up with the center.
  3. Write the letters of your choice on the tape for reference and to help with spacing.
  4. Select your first stamp. When holding the stamp, make sure the ImpresssArt logo is facing you so the letter or design will be stamped in the correct orientation.
  5. Hold your stamp on the blank and lightly drag it toward the edge of the tape; strike each letter once with medium force.
  6. Using the hole punch pliers, punch hole if your previously marked area.
  7. Highlight your impression with the enamel marker. Wait 1-3 minutes and wipe away excess with a soft cloth.
  8. Find the center of your 18" chain, and cut at center link using the flush cutters.
  9. Use two pairs of chain nose pliers to open the jump ring laterally.
  10. Thread the jump ring through the first hole and attach to the end link of the 18" chain.
  11. Close the jump ring by bending it laterally so that the ends pass one another.
  12. Apply the last 3 steps to the other side.